Fundamental Plumber Insights for Installing a Bathtub
Fundamental Plumber Insights for Installing a Bathtub
Blog Article
Just how do you really feel about How to Install a Bathtub?
Installing a bathtub isn't precisely rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily available, the project can relocate speedily; if you have to open a wall to remove the old bathtub as well as position the new bath tub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and embeded in the brand-new one. Ensure you have qualified yourself for the work and are comfortable attempting it. Rather than hiring a professional to take control of a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will certainly assist you set up a new bathtub in your bathroom if you have actually currently purchased a new tub and do not require to change the arrangement of your previous water supply pipelines.
Your tools as well as material list ought to comprise the following:
Getting ready for the Setup
To start with, the sustaining framework supplied with the bath must be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to prevent strain on the tub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its final placement.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water supply. After doing so, activate the taps to drain any water staying in the system. The procedure of getting rid of the existing faucets can be quite bothersome as a result of the limited gain access to that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before proceeding to fit the new faucets, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, place the tub in the required position. The wood boards are handy in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the level and adjusting the feet on the bath tub till the level reviews level.
To set up taps, fit the bottom of the outermost flexible tap port to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the supply of water and inspect all joints and also brand-new pipework for leaks and also tighten them if required. Fill up the tub as well as additionally check the overflow outlet and the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bathtub must wait until the bath tub has been made use of at the very least when as this will resolve it right into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin making certain that the washing machines remain in location in between the faucet and also the sink. Secure the faucet in position with the maker given backnut. When the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The former kind needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a stiff seal, triggering the water to permeate the wall surface in between the bath and the tiling, resulting in problems with dampness and feasible leaks to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can split rather early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
I came across that content about A Step-by-Step Guide to Installing a Bathtub while scouting around the internet. Be sure to take a moment to share this blog if you enjoyed reading it. We enjoy reading our article about How to Install a Bathtub.
Avoid further plumbing damage; call. Report this page